A relatively primitive design compared to the Mark I Construction Drone, the ASD1 is a reliable replacement in a compact form.

Designed to be an inexpensive replacement for the Mark I Construction Drone, the ASD1 uses reliable technology to do more work with less.

The ASD1 has a smaller chassis, no armor, and a usage of Arcjets for propulsion.

The ASD1 is specialized in:

• Deep Space/Orbital Construction
• Starship Repair

The ASD1 has a stubby, sloped head section with a large mono-eye visual sensor and four telescopic arms (two on top of the head and two on the sides). A long, flat rear section is used for storage of arm attachments and small materials. Underneath the flat section is a rotating joint with a series of three Arcjets attached to each side.

Side view without arms

Designed in YE 29, the Mark I Construction Drone was an awkward drone design when it was first rolled off the assembly lines. Large and fast, it had a difficult time working in shipyard environments due to its fusion engine. While good in Deep Space Operations, there were still quite a few accidents due to it's fusion engine melting projects.

Because of this, Kaiserlich F&E went back to the drawing board entirely. Designing the ASD1 in YE 33, the scientific team used old technology from the After Conflict Era and combined them with modern design philosophies and material sciences. Slower and smaller than it's predecessor, the ASD1 is believed to be a more cost-efficient and effective way to minimize orbital/deep space construction accidents as well as increase productivity. It is also safer to operate near active startships in need of repair.

Class: ASD1 Type: Autonomous Drone Designers: Kaiserlich F&E Manufacturer: Abwehran Imperial Yards Production: Mass-produced¹⁾ Fielded by: Everyone; 31,000 Credits per unit (11,000 KS)

Crew: 1x drone_vims

Length: 2 meters (~6.6 feet) Width: 1.6 meters (~5.2 feet) Height: 0.7 meters (~2.3 feet)

Sublight Engines: 200 m/s (3 Gs) Range: 48 hours Lifespan: 2 Abwehran Years Refit Cycle: To be recycled after 2 Abwehran Years (8 Standard Years)

See Damage Rating (Version 3) for an explanation of the damage system.

• Hull: 5 Armor SP

Small Access hatches located in 20 points to allow Mechanics access to all of the ASD1's vital systems. They are only large enough to reach into and cannot fit humanoids.

The ASD1 does not have armor at all, but uses a standard civilian hull structure on top of a chassis of titanium trusses.

The ASD1 runs its Drone Virtual Intelligence Model upon a CU-23.

• Radio, Civilian Small Craft

• Civilian Radar

A pair of struts protruding from the 'head' section hold a pair of anchors and 1 kilometer of woven, carbon-nanotube cables each. One anchor is a barbed dart used to pierce rock or soft debris to hold the ASD1 in place while the second type of anchor is a magnetic plate used for metallic objects.

The ASD1 has four telescopic arms located around it's 'head' section. Each arm has the ability to fit a different type of tool and can extend to a full length of 2 meters beyond the drone's chassis.

A tri-finger clamp attachment, the Grappler is used to physically grab debris or construction material.

A simple free-elecron laser that is used to either wield material together or cut it apart. It can also be used in mining operations to cut off chunks of asteroids for transport to refinery vessels.

A five-finger attachment resembling a hand, the Manipulator is designed for more delicate work and is especially designed to minimize pressing in order to protect against crushing valuable building materials.

Many of the main systems use a pair of solar-charged batteries to power it's equipment and AI. However it does have a D-H3 Secondary Fusion Reactor to power it's sub-light engines.

The ASD1 is the first design to using 6 Arcjet motors to propel itself around a damaged vessel or a ship yard.