STAR ARMY

Sci-fi roleplaying and worldbuilding community

User Tools

Site Tools

Trace: • Star Army Personnel Command • Project of the Lazarus Consortium • Major Battles • Star Army Wiki • HHG ‘High Hybrid Gun’ • Longsword Class Frigate • YE 43 • Ke-M2-W4300 Aether Whip
corp:mining_guild:equipment:plasma_cutter_torch

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Last revisionBoth sides next revision
corp:mining_guild:equipment:plasma_cutter_torch [2023/12/21 04:21] – external edit 127.0.0.1corp:mining_guild:equipment:plasma_cutter_torch [2024/04/30 22:47] – [Weapon Mechanisms] charaa
Line 51: Line 51:
 Weapon mechanisms can be found below: Weapon mechanisms can be found below:
  
-  * Firing Mechanism+  * Firing Mechanism: When using the detached version the battery recharges the Plasma Cutter/Torch for ten minutes after use. When using the version attached to the Power Armor,  there is no delay since there is no need for recharging. 
  
-When using the detached version the battery recharges the Plasma Cutter/Torch for ten minutes after use. When using the version attached to the Power Armor,  there is no delay since there is no need for recharging. +  * Loading: The Plasma Cutter/Torch uses the power of the Power Armor itself and due to this, it is loaded with a plasma cell, created by the NDC. After a switch from using the Mole Claws, due to which the Plasma Cutter/Torch is turned off for safety reasons, there is a short 0.01-second delay. When using the detached version, the Power pack is added at the bottom of the Plasma Cutter Torch.
  
-  * Loading+  * Mode Selector: Each Power armor has a HUD, and through an image, the Plasma Cutter/Torch will enter the rock cutting mode, which allows it to be used, or a shut off mode, if the Miner has to vacate for whatever reason and also a switch to change whether the Miner needs to use the Mole Claws or the Plasma Cutter/Torch. The detached version has a button at the back.
  
-The Plasma Cutter/Torch uses the power of the Power Armor itself and due to this, it is loaded with a plasma cell, created by the NDC. After a switch from using the Mole Claws, due to which the Plasma Cutter/Torch is turned off for safety reasons, there is a short 0.01-second delay. When using the detached version, the Power pack is added at the bottom of the Plasma Cutter Torch.+  * Firing Modes: When using the Plasma Cutter/Torch there is only a single firing mode which is a beam based firing mode in order to make a precise penetration of hard rocks. 
  
-  * Mode Selector +  * Safety Mechanism: Plasma Cutter/Torch cease functioning when the Miner switches to The Mole Claws, and if the Power Armor is turned for whatever reason and not facing a wall of dirt and rock, the Miner will see a huge X on their screen and both the Plasma Cutter/Torch and the Mole Claws stop working until they are in the proper position.
  
-Each Power armor has a HUD, and through an image, the Plasma Cutter/Torch will enter the rock cutting mode, which allows it to be used, or a shut off mode, if the Miner has to vacate for whatever reason and also a switch to change whether the Miner needs to use the Mole Claws or the Plasma Cutter/Torch. The detached version has a button at the back. +  * Weapon Sight: When attached to the Power armor, the Helmet has a View screen in the HUD that would allow the Miner to get a clear picture of what they are targeting. The Plasma Cutter/Torch addition adds the targeting mark in front of them on the screen that allows for the precise targeting so that the rock can be penetrated. The Mineral Scanners will allow them to see if they are getting any ore or not.
- +
-  * Firing Modes +
- +
-When using the Plasma Cutter/Torch there is only a single firing mode which is a beam based firing mode in order to make a precise penetration of hard rocks.  +
- +
-  * Safety Mechanism +
- +
-Plasma Cutter/Torch cease functioning when the Miner switches to The Mole Claws, and if the Power Armor is turned for whatever reason and not facing a wall of dirt and rock, the Miner will see a huge X on their screen and both the Plasma Cutter/Torch and the Mole Claws stop working until they are in the proper position. +
- +
-  * Weapon Sight +
- +
-When attached to the Power armor, the Helmet has a View screen in the HUD that would allow the Miner to get a clear picture of what they are targeting. The Plasma Cutter/Torch addition adds the targeting mark in front of them on the screen that allows for the precise targeting so that the rock can be penetrated. The Mineral Scanners will allow them to see if they are getting any ore or not.+
  
 The detached version has a targeting screen at the back of it, for targeting as well.   The detached version has a targeting screen at the back of it, for targeting as well.  

corp/mining_guild/equipment/plasma_cutter_torch.txt · Last modified: 2024/04/30 22:48 by charaa

Page Tools

Content copyright StarArmy.com and/or individual contributors and used under license. Star Army is a registered trademark.
Terms of Service - Privacy Policy